Guida al passo delle cinghie modulari in plastica
Pitch is the centre-to-centre spacing of repeating hinge or module geometry. It is a powerful identifier, but it does not define the conveying face, underside or sprocket compatibility by itself.
What pitch measures
Pitch is the repeating distance in the modular hinge/module geometry. In replacement work, measure across several repeats and divide by the number of pitches rather than relying on one worn edge. This reduces error and helps distinguish neighbouring nominal families.
Pitch family reference
| Pece | Direzione familiare | Practical selection note |
|---|---|---|
| 12,7 mm | Esempi piatti/chiusi | Passo fine; un utile punto di partenza per trasferimenti compatti e supporti per piccoli prodotti. |
| 15,2 mm | Esempi di configurazione a griglia aperta Flat + 14% / 28% | Famiglia di viti a passo fine con opzioni di supporto continuo e apertura del processo. |
| 19,05 mm | Esempio di griglia aperta Flat + 16% | Famiglia di fibre medio-fini, adatte a terreni rettilinei o con drenaggio moderato. |
| 25 mm | Esempio di griglia aperta 29% + raggio 52% | Passo di riga ampio e generico con esempi rettilinei e curvi. |
| 25,4 mm | Esempi di piatto + 8% / 34% / 35% dritto + raggio 47% / 55% | In questo confronto si riscontra la più ampia varietà di volti e percorsi di corsa. |
| 27,2 mm | Esempi di griglia aperta 38% | Riferimento rettilineo ad area aperta più elevata. |
| 50,8 mm | Appartamento/speciale + un esempio aperto 20% | Famiglia di eliche a passo maggiore per applicazioni in cui il trasferimento di precisione non è l'aspetto principale. |
| 63,5 mm | Esempio piatto/chiuso | Passo maggiore mostrato in questa gamma di confronto tra cinghie modulari. |
Pitch and transfer geometry
Smaller pitch often supports compact transfer geometry because the module and sprocket system can be correspondingly finer. That does not guarantee a specific minimum transfer diameter. The actual belt edge, hinge and sprocket geometry must still be confirmed.
Pitch and product footprint
Pitch is not the same as opening size. A fine-pitch open belt can still have openings that matter to a small product, while a larger-pitch flat belt can provide continuous top support. Look at the face pattern and product footprint together.
Pitch and sprockets
The drive pitch must correspond to the belt family, but compatibility goes further: underside tooth engagement, sprocket thickness/form, tooth count, bore/shaft and spacing all matter. This is why a pitch-only replacement can fail even when the nominal number is correct.
Replacement measurement method
| Measurement | Method |
|---|---|
| Pece | Measure several repeating centres and divide |
| Width | Measure overall belt width and edge/module detail |
| Top face | Photograph pattern/opening and any flights/attachments |
| Underside | Photograph drive/hinge geometry |
| Sprocket | Photograph engaged teeth and record shaft/bore |
| Sentiero | Record straight or radius conveyor geometry |
When to use the pitch as a search term
Pitch-specific product pages are useful because they narrow the mechanical family for buyers. They should not be treated as proof that all surfaces, widths or materials are available at that pitch. Use the pitch to enter the range, then confirm the final configuration.
Worked identification example
Suppose an existing belt appears to be about 25 mm pitch. Measure ten repeating hinge centres instead of one module, then divide the total by ten. Next record the overall width, face pattern and underside. If the conveyor includes a horizontal curve, the 25 mm measurement does not point to the same family as a straight 25 mm belt. The curve geometry becomes a separate deciding input.
The same method is useful at 25.4 mm, where this range contains flat, open-grid, specialty and radius directions. Pitch narrows the search; the other geometry completes it.
Need help narrowing the configuration?
Send the information you already have. Missing fields can be identified during review rather than guessed.
