{"id":540,"date":"2026-09-09T06:18:04","date_gmt":"2026-09-09T06:18:04","guid":{"rendered":"https:\/\/modularbelt.net\/product\/19-05-mm-pitch-flat-surface-plastic-modular-belt\/"},"modified":"2026-09-09T07:53:13","modified_gmt":"2026-09-09T07:53:13","slug":"19-05-mm-pitch-flat-surface-plastic-modular-belt","status":"publish","type":"product","link":"https:\/\/modularbelt.net\/uk\/product\/19-05-mm-pitch-flat-surface-plastic-modular-belt\/","title":{"rendered":"\u041f\u043b\u0430\u0441\u0442\u0438\u043a\u043e\u0432\u0438\u0439 \u043c\u043e\u0434\u0443\u043b\u044c\u043d\u0438\u0439 \u0440\u0435\u043c\u0456\u043d\u044c \u0437 \u043f\u043b\u043e\u0441\u043a\u043e\u044e \u043f\u043e\u0432\u0435\u0440\u0445\u043d\u0435\u044e \u0442\u0430 \u043a\u0440\u043e\u043a\u043e\u043c 19,05 \u043c\u043c"},"content":{"rendered":"
\n
\n

Configuration overview<\/h2>\n
\n
\n
\n
\"\u041f\u043b\u0430\u0441\u0442\u0438\u043a\u043e\u0432\u0438\u0439<\/figure>\n<\/div>\n<\/div>\n
\n

Mid-fine pitch for stable carrying and conveyor layouts that do not need open area.<\/p>\n

For 19.05 mm Pitch Flat Surface Plastic Modular Belt: The 19.05 mm reference group includes both flat and 16% open-grid directions. Selection therefore turns on process function and face geometry after the pitch is known.<\/p>\n

Configuration identity<\/strong><\/p>\n

The public name for 19.05 mm Pitch Flat Surface Plastic Modular Belt uses measurable pitch, face and path. Short legacy abbreviations are not presented as EVER POWER model codes.<\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/div>\n<\/section>\n

\n
\n

Technical specification reference<\/h2>\n
\n\n\n\n\n\n\n\n\n\n\n\n\n\n
Parameter<\/th>\nSpecification \/ RFQ reference<\/th>\n<\/tr>\n<\/thead>\n
Pitch<\/td>\n19.05 mm<\/td>\n<\/tr>\n
Conveying face<\/td>\nFlat \/ closed face<\/td>\n<\/tr>\n
Open area reference<\/td>\nNot specified<\/td>\n<\/tr>\n
Running path<\/td>\nStraight<\/td>\n<\/tr>\n
Belt width<\/td>\nProject-specific – state required width or measure existing belt<\/td>\n<\/tr>\n
Overall belt length \/ conveyor centres<\/td>\nProject-specific – provide drawing or measured layout<\/td>\n<\/tr>\n
Connecting pin \/ hinge<\/td>\nConfirm from ordered family or replacement sample<\/td>\n<\/tr>\n
Material<\/td>\nConfirm against environment, temperature, product\/contact and documentation requirement<\/td>\n<\/tr>\n
Drive interface<\/td>\nConfirm belt underside, sprocket tooth form\/count, bore\/shaft and sprocket spacing<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/section>\n
\n
\n

Product support and transfer behaviour<\/h2>\n
\n
\n
\"Stable-support<\/figure>\n<\/div>\n
\n

The closed face of 19.05 mm Pitch Flat Surface Plastic Modular Belt is a useful direction when stable product support is more important than through-belt drainage. Check the smallest product footprint and the transfer geometry between conveyor sections or machines.<\/p>\n

If the product carried on 19.05 mm Pitch Flat Surface Plastic Modular Belt is soft, delicate or mark-sensitive, include that in the RFQ. Review surface geometry as part of handling performance rather than assuming it from a generic flat-top description.<\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/section>\n

\n
\n

Sprocket and drive matching<\/h2>\n
\n
\n
\n
\"Split<\/figure>\n
\"Single-piece<\/figure>\n<\/div>\n<\/div>\n
\n

19.05 mm Pitch Flat Surface Plastic Modular Belt is positively driven through engagement between its underside and the sprockets. The 19.05 mm pitch narrows the drive family, but tooth form, tooth count, sprocket construction, bore or shaft profile and spacing across the belt still have to agree with this configuration.<\/p>\n

For a 19.05 mm Pitch Flat Surface Plastic Modular Belt replacement, photograph a sprocket while it is engaged with the belt and add a second view of the shaft. If new sprockets are required, provide the shaft diameter or profile and any split or one-piece maintenance preference.<\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/section>\n

\n
\n

Support, guide and wear interfaces<\/h2>\n
\n
\n
\n
\"Wear<\/figure>\n
\"Guide<\/figure>\n<\/div>\n<\/div>\n
\n

19.05 mm Pitch Flat Surface Plastic Modular Belt is supported and located by the conveyor frame. Record wear-strip or guide-profile dimensions when the existing support system will be retained. Uneven edge or support wear can indicate alignment or guide-load problems that replacing this belt alone will not correct.<\/p>\n

For a new conveyor using 19.05 mm Pitch Flat Surface Plastic Modular Belt, show the proposed support-track layout, return path and any side guides. If the layout includes a radius, give particular attention to the inner and outer guide paths.<\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/section>\n

\n
\n

Application direction<\/h2>\n
\n\n\n\n\n\n\n\n\n\n\n
Application question<\/th>\nSelection implication<\/th>\n<\/tr>\n<\/thead>\n
What is being conveyed?<\/td>\nProduct footprint, stability, marking sensitivity and contamination risk<\/td>\n<\/tr>\n
What must pass through the belt?<\/td>\nWater, air or debris may require an open face<\/td>\n<\/tr>\n
Straight or curved path?<\/td>\nDefines straight versus radius family before face selection<\/td>\n<\/tr>\n
How small are the transfers?<\/td>\nPitch, edge and sprocket geometry become more important<\/td>\n<\/tr>\n
Wet, dry, cold, warm or chemically cleaned?<\/td>\nMaterial and documentation must be confirmed for the ordered configuration<\/td>\n<\/tr>\n
Accumulation or frequent starts\/stops?<\/td>\nDescribe duty cycle and product behaviour for review<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/section>\n
\n
\n

Replacement identification workflow<\/h2>\n

When identifying a replacement for 19.05 mm Pitch Flat Surface Plastic Modular Belt, measure pitch across several repeating hinge centres rather than one worn module. Record overall belt width, photograph the top surface, underside, hinge or pin and edge, then add a sprocket-engagement image. Note whether the conveyor is straight or radius and mark the flow direction. If an old code is readable, include it as an additional reference rather than the only matching evidence.<\/p>\n

This measurement-led method is especially important for 19.05 mm Pitch Flat Surface Plastic Modular Belt, because the nominal pitch alone may also appear in other face or running-path families.<\/p>\n<\/div>\n<\/section>\n

\n
\n

Installation and maintenance checks<\/h2>\n
\n\n\n\n\n\n\n\n\n\n\n
Check<\/th>\nPractical reason<\/th>\n<\/tr>\n<\/thead>\n
Sprocket alignment and spacing<\/td>\nAvoid uneven positive-drive engagement<\/td>\n<\/tr>\n
Guide \/ wear-strip condition<\/td>\nAvoid transferring an old wear or tracking problem to the new belt<\/td>\n<\/tr>\n
Pin retention<\/td>\nConfirm hinge assembly and maintenance access<\/td>\n<\/tr>\n
Transfers and dead plates<\/td>\nCheck product hand-off with the selected pitch\/edge geometry<\/td>\n<\/tr>\n
Cleaning access<\/td>\nMatch the actual sanitation\/maintenance routine<\/td>\n<\/tr>\n
Post-install observation<\/td>\nWatch tracking, edge wear, unusual noise and product stability before full-rate production<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/section>\n
\n
\n

Documentation and customization<\/h2>\n

Custom width, belt length and related accessories for 19.05 mm Pitch Flat Surface Plastic Modular Belt are reviewed from the project dimensions. Request material, product-contact, inspection or other documentation explicitly so the requirement is tied to this ordered configuration. No compliance or performance claim is inferred from colour or a family photograph.<\/p>\n<\/div>\n<\/section>\n

\n
\n

RFQ checklist for this belt<\/h2>\n
\n\n\n\n\n\n\n\n\n\n\n\n\n
Send<\/th>\nWhy it matters<\/th>\n<\/tr>\n<\/thead>\n
Conveyed product and process step<\/td>\nDefines support, drainage\/release and cleaning requirements<\/td>\n<\/tr>\n
Belt pitch and required width<\/td>\nNarrows family and module build<\/td>\n<\/tr>\n
Face\/open area if known<\/td>\nDifferentiates process geometry<\/td>\n<\/tr>\n
Straight\/curve path; radius + angle if curved<\/td>\nDefines running-path family<\/td>\n<\/tr>\n
Load, speed and operating environment<\/td>\nProvides duty context<\/td>\n<\/tr>\n
Sprocket\/shaft\/underside details<\/td>\nProtects drive compatibility<\/td>\n<\/tr>\n
Guide\/wear-strip profile if retained<\/td>\nProtects frame interface<\/td>\n<\/tr>\n
Quantity, destination and required documents<\/td>\nCompletes commercial\/documentation scope<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/section>\n
\n
\n

Frequently asked questions<\/h2>\n
\n

Can I select this belt from pitch alone?<\/h3>\n

No. Pitch is a strong identifier, but face, underside, width, running path and sprocket engagement also need to match.<\/p>\n

Can the listed open-area value be treated as a performance rating?<\/h3>\n

No. It is a geometry reference. Drainage, airflow and product handling depend on the complete conveyor and ordered configuration.<\/p>\n

What if I only have an old belt and no drawing?<\/h3>\n

Send clear photographs plus pitch and width measurements. Existing sprocket and guide details are very helpful for replacement work.<\/p>\n<\/div>\n<\/div>\n<\/section>\n

\n
\n

Request configuration review<\/h2>\n

For 19.05 mm Pitch Flat Surface Plastic Modular Belt, send the dimensions, photos or drawings you already have. Missing variables can be identified during review rather than guessed.<\/p>\n

Send RFQ<\/a><\/p>\n<\/div>\n<\/section>","protected":false},"excerpt":{"rendered":"

Mid-fine pitch for stable carrying and conveyor layouts that do not need open area.<\/p>","protected":false},"featured_media":458,"comment_status":"open","ping_status":"closed","template":"","meta":[],"product_cat":[930],"product_tag":[940,937,938],"class_list":["post-540","product","type-product","status-publish","has-post-thumbnail","product_cat-flat-surface-plastic-modular-belts","product_tag-19-05-mm","product_tag-plastic-modular-belt","product_tag-straight","first","instock","shipping-taxable","product-type-simple"],"_links":{"self":[{"href":"https:\/\/modularbelt.net\/uk\/wp-json\/wp\/v2\/product\/540","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/modularbelt.net\/uk\/wp-json\/wp\/v2\/product"}],"about":[{"href":"https:\/\/modularbelt.net\/uk\/wp-json\/wp\/v2\/types\/product"}],"replies":[{"embeddable":true,"href":"https:\/\/modularbelt.net\/uk\/wp-json\/wp\/v2\/comments?post=540"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/modularbelt.net\/uk\/wp-json\/wp\/v2\/media\/458"}],"wp:attachment":[{"href":"https:\/\/modularbelt.net\/uk\/wp-json\/wp\/v2\/media?parent=540"}],"wp:term":[{"taxonomy":"product_cat","embeddable":true,"href":"https:\/\/modularbelt.net\/uk\/wp-json\/wp\/v2\/product_cat?post=540"},{"taxonomy":"product_tag","embeddable":true,"href":"https:\/\/modularbelt.net\/uk\/wp-json\/wp\/v2\/product_tag?post=540"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}