{"id":529,"date":"2026-09-09T06:17:36","date_gmt":"2026-09-09T06:17:36","guid":{"rendered":"https:\/\/modularbelt.net\/plastic-modular-belt-pitch-guide\/"},"modified":"2026-09-09T07:52:48","modified_gmt":"2026-09-09T07:52:48","slug":"plastic-modular-belt-pitch-guide","status":"publish","type":"post","link":"https:\/\/modularbelt.net\/it\/plastic-modular-belt-pitch-guide\/","title":{"rendered":"Guida al passo delle cinghie modulari in plastica"},"content":{"rendered":"
\n
\n

Guida al passo delle cinghie modulari in plastica<\/h1>\n

Il passo \u00e8 la distanza tra i centri delle geometrie ripetitive di cerniere o moduli. \u00c8 un identificatore importante, ma da solo non definisce la superficie di trasporto, la parte inferiore o la compatibilit\u00e0 con le ruote dentate.<\/p>\n<\/div>\n<\/section>\n

\n
\n

What pitch measures<\/h2>\n
\n
\n
\"Fine-pitch<\/figure>\n<\/div>\n
\n

Pitch is the repeating distance in the modular hinge\/module geometry. In replacement work, measure across several repeats and divide by the number of pitches rather than relying on one worn edge. This reduces error and helps distinguish neighbouring nominal families.<\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/section>\n

\n
\n

Pitch family reference<\/h2>\n
\n\n\n\n\n\n\n\n\n\n\n\n\n
Pece<\/th>\nDirezione familiare<\/th>\nPractical selection note<\/th>\n<\/tr>\n<\/thead>\n
12,7 mm<\/td>\nEsempi piatti\/chiusi<\/td>\nPasso fine; un utile punto di partenza per trasferimenti compatti e supporti per piccoli prodotti.<\/td>\n<\/tr>\n
15,2 mm<\/td>\nEsempi di configurazione a griglia aperta Flat + 14% \/ 28%<\/td>\nFamiglia di viti a passo fine con opzioni di supporto continuo e apertura del processo.<\/td>\n<\/tr>\n
19,05 mm<\/td>\nEsempio di griglia aperta Flat + 16%<\/td>\nFamiglia di fibre medio-fini, adatte a terreni rettilinei o con drenaggio moderato.<\/td>\n<\/tr>\n
25 mm<\/td>\nEsempio di griglia aperta 29% + raggio 52%<\/td>\nPasso di riga ampio e generico con esempi rettilinei e curvi.<\/td>\n<\/tr>\n
25,4 mm<\/td>\nEsempi di piatto + 8% \/ 34% \/ 35% dritto + raggio 47% \/ 55%<\/td>\nIn questo confronto si riscontra la pi\u00f9 ampia variet\u00e0 di volti e percorsi di corsa.<\/td>\n<\/tr>\n
27,2 mm<\/td>\nEsempi di griglia aperta 38%<\/td>\nRiferimento rettilineo ad area aperta pi\u00f9 elevata.<\/td>\n<\/tr>\n
50,8 mm<\/td>\nAppartamento\/speciale + un esempio aperto 20%<\/td>\nFamiglia di eliche a passo maggiore per applicazioni in cui il trasferimento di precisione non \u00e8 l'aspetto principale.<\/td>\n<\/tr>\n
63,5 mm<\/td>\nEsempio piatto\/chiuso<\/td>\nPasso maggiore mostrato in questa gamma di confronto tra cinghie modulari.<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/section>\n
\n
\n

Pitch and transfer geometry<\/h2>\n

Smaller pitch often supports compact transfer geometry because the module and sprocket system can be correspondingly finer. That does not guarantee a specific minimum transfer diameter. The actual belt edge, hinge and sprocket geometry must still be confirmed.<\/p>\n<\/div>\n<\/section>\n

\n
\n

Pitch and product footprint<\/h2>\n

Pitch is not the same as opening size. A fine-pitch open belt can still have openings that matter to a small product, while a larger-pitch flat belt can provide continuous top support. Look at the face pattern and product footprint together.<\/p>\n<\/div>\n<\/section>\n

\n
\n

Pitch and sprockets<\/h2>\n
\n
\n
\"Single-piece<\/figure>\n<\/div>\n
\n

The drive pitch must correspond to the belt family, but compatibility goes further: underside tooth engagement, sprocket thickness\/form, tooth count, bore\/shaft and spacing all matter. This is why a pitch-only replacement can fail even when the nominal number is correct.<\/p>\n<\/div>\n<\/div>\n<\/div>\n<\/section>\n

\n
\n

Replacement measurement method<\/h2>\n
\n\n\n\n\n\n\n\n\n\n\n
Measurement<\/th>\nMethod<\/th>\n<\/tr>\n<\/thead>\n
Pece<\/td>\nMeasure several repeating centres and divide<\/td>\n<\/tr>\n
Width<\/td>\nMeasure overall belt width and edge\/module detail<\/td>\n<\/tr>\n
Top face<\/td>\nPhotograph pattern\/opening and any flights\/attachments<\/td>\n<\/tr>\n
Underside<\/td>\nPhotograph drive\/hinge geometry<\/td>\n<\/tr>\n
Sprocket<\/td>\nPhotograph engaged teeth and record shaft\/bore<\/td>\n<\/tr>\n
Sentiero<\/td>\nRecord straight or radius conveyor geometry<\/td>\n<\/tr>\n<\/tbody>\n<\/table>\n<\/div>\n<\/div>\n<\/section>\n
\n
\n

When to use the pitch as a search term<\/h2>\n

Pitch-specific product pages are useful because they narrow the mechanical family for buyers. They should not be treated as proof that all surfaces, widths or materials are available at that pitch. Use the pitch to enter the range, then confirm the final configuration.<\/p>\n<\/div>\n<\/section>\n

\n
\n

Worked identification example<\/h2>\n

Suppose an existing belt appears to be about 25 mm pitch. Measure ten repeating hinge centres instead of one module, then divide the total by ten. Next record the overall width, face pattern and underside. If the conveyor includes a horizontal curve, the 25 mm measurement does not point to the same family as a straight 25 mm belt. The curve geometry becomes a separate deciding input.<\/p>\n

The same method is useful at 25.4 mm, where this range contains flat, open-grid, specialty and radius directions. Pitch narrows the search; the other geometry completes it.<\/p>\n<\/div>\n<\/section>\n

\n
\n

Need help narrowing the configuration?<\/h2>\n

Send the information you already have. Missing fields can be identified during review rather than guessed.<\/p>\n

Invia richiesta di preventivo<\/a><\/p>\n<\/div>\n<\/section>","protected":false},"excerpt":{"rendered":"

Il passo \u00e8 la distanza tra i centri delle geometrie ripetitive di cerniere o moduli. \u00c8 un identificatore importante, ma da solo non definisce la superficie di trasporto, la parte inferiore o la compatibilit\u00e0 con le ruote dentate.<\/p>","protected":false},"author":1,"featured_media":455,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[],"class_list":["post-529","post","type-post","status-publish","format-standard","has-post-thumbnail","hentry","category-uncategorized"],"_links":{"self":[{"href":"https:\/\/modularbelt.net\/it\/wp-json\/wp\/v2\/posts\/529","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/modularbelt.net\/it\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/modularbelt.net\/it\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/modularbelt.net\/it\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/modularbelt.net\/it\/wp-json\/wp\/v2\/comments?post=529"}],"version-history":[{"count":1,"href":"https:\/\/modularbelt.net\/it\/wp-json\/wp\/v2\/posts\/529\/revisions"}],"predecessor-version":[{"id":591,"href":"https:\/\/modularbelt.net\/it\/wp-json\/wp\/v2\/posts\/529\/revisions\/591"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/modularbelt.net\/it\/wp-json\/wp\/v2\/media\/455"}],"wp:attachment":[{"href":"https:\/\/modularbelt.net\/it\/wp-json\/wp\/v2\/media?parent=529"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/modularbelt.net\/it\/wp-json\/wp\/v2\/categories?post=529"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/modularbelt.net\/it\/wp-json\/wp\/v2\/tags?post=529"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}